PENGARUH SUDUT PAHAT PADA PENGGURDIAN KOMPOSIT SERAT DAUN NANAS / TERMOPLASTIK PADA PEMBENTUKAN DELAMINASI

Zulkarnain Zulkarnain, Ismet Hari Mulyadi, Jupri Jupri, Siswandi B

Abstract


This study aims to determine the effect of the Gurdi tool angle on delamination in composite laminates in the formation of delaminations. The spacing of the selected reinforcing fibers was 2.4 and 6 mm in a composite laminate of ethylene vinyl acetate (EVA) polymer matrix with reinforcing fibers from pineapple leaves. The method used in composite fabrication is hand lay-up, namely by direct casting on three layers of fiber that has been woven and tied to the sides of the mold. For cutting speed, Vf 72 mm / min, using a chisel with a diameter of 8 mm with a tool angle of 70o and 118o. Delamination was determined using the Feda method. The delamination sections were observed using a digital microscope and then processed using AutoCAD to measure Dmax and Ad. The delamination ratio in the top hole for the tool diameter of 8mm with a 70° angle at the variation of the distance of 2 mm, 4 mm and 6 mm were 1.268, 1.224 and 1.192 for the bottom hole were 1.078, 1.042 and 1.029, respectively. Meanwhile, the ratio of delamination in the upper hole for a tool diameter of 8mm with an angle of 118° at a distance variation of 2mm, 4mm and 6mm were 1.194, 1.194, 1.158 for the bottom hole, respectively, 1.046, 1.042 and 1.038.

Keywords


Delamination; laminate composites; ethylene vinyl acetate; pineapple leaf fiber; drilling process

Full Text:

PDF

References


F. Hussain, M. Hojjati, M. Okamoto, and R. E. Gorga, “Polymer-matrix nanocomposites, processing, manufacturing, and application: An overview,†J. Compos. Mater., vol. 40, no.17, pp. 1511–1575, 2006.

Widyorini, Ragil; Sari, Nasmi Herlina; Setiyo, Muji; Refiadi, Gunawan (2021-11-06). "The Role of Composites for Sustainable Society and Industry". Mechanical Engineering for Society and Industry (dalam bahasa Inggris). 1 (2): 48–53. doi:10.31603/mesi.6188. ISSN 2798-5245.

Respati, Sri Mulyo Bondan; Purwanto, Helmy; Fakhrudin, Ilham; Prayitno, Pungkas (2021-07-29). "Tensile Strength and Density Evaluation of Composites from Waste Cotton Fabrics and High-Density Polyethylene (HDPE): Contributions to the Composite Industry and a Cleaner Environment". Mechanical Engineering for Society and Industry (dalam bahasa Inggris). 1 (1): 41–47. doi:10.31603/mesi.5252. ISSN 2798-5245.

K. L. Pickering, M. G. A. Efendy, and T.M. Le, “A review of recent developments in natural fibre composites and their mechanical performance,†Compos. Part A Appl. Sci. Manuf., vol. 83, pp. 98–112, 2016.

M. Asrofi, H. Abral, Y. K. Putra, S. M.Sapuan, and H. J. Kim, “Effect of duration of sonication during gelatinization on properties of tapioca starch water hyacinth fiber biocomposite,†Int. J. Biol. Macromol., vol. 108, pp. 167–176, 2018.

H. Abral, G. J. Putra, M. Asrofi, J.-W.Park, and H.-J. Kim, “Effect of vibration duration of high ultrasound applied to bio- composite while gelatinized on its properties,†Ultrason. Sonochem., vol. 40,2018.

R. A. Ilyas, S. M. Sapuan, M. R. Ishak, and E. S. Zainudin, “Development and characterization of sugar palm nanocrystalline cellulose reinforced sugar palm starch bionanocomposites,†Carbohydr. Polym., vol. 202, pp. 186–202, 2018.

E. Syafri et al., “Synthesis and characterization of cellulose nanofibers (CNF) ramie reinforced cassava starch hybrid composites,†Int. J. Biol. Macromol., vol. 120, pp. 578–586, 2018.

K. Z. M. A. Motaleb, M. S. Islam, and M. . Hoque, “Improvement of Physicomechanical Properties of Pineapple Leaf Fiber Reinforced Composite,†Int. J. Biomater., vol. 2018, 2018.

M. Asim et al., “A Review on Pineapple Leaves Fibre and Its Composites,†Int. J. Polym. Sci., vol. 2015, pp. 1–16, 2015.

H. Abral et al., “Mechanical properties of water hyacinth fibers - polyester composites before and after immersion in water,†Mater. Des., vol. 58, pp. 125–129,2014.

D. F. Liu, Y. J. Tang, and W. L. Cong, “Areview of mechanical drilling for composite laminates,†Compos. Struct., vol. 94, no. 4, pp. 1265–1279, 2012.




DOI: https://doi.org/10.35314/ip.v13i1.3325

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 INOVTEK POLBENG


This Journal has been listed and indexed in :

         

Creative Commons License
inovtek polbeng by http://ejournal.polbeng.ac.id/index.php/IP is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License